Tuesday, December 7, 2010

Insane Weights for the Aeron

My wife was shooting the Aeron B96 a few weeks ago and found it to be a bit too heavy. Removing the weight was helpful, but now it's too light at the muzzle. I wondered if there was a compromise.



The factory supplied steel weight is 24.5mm in diameter, 24mm long, and weighs 78 grams.

Before she shot it, I was actually using it with two 78g weights attached. The weights slide onto an 8mm diameter rod and secure with a single M5 setscrew. The weight(s) can be located anywhere on the rod and fixed to achieve the balance characteristics that the shooter wants. A slightly heavy muzzle is often preferred.

I cut a piece of 7/8" diameter aluminum rod to make some new (light weight!) weights.

Faced off the end then skim cut to get a nice finish.

Center drilled.

Then gradually through drilled.

5/16" is pretty close to 8mm. Turned out to be an OK fit.

With a parting tool, I cut off a 24mm long cylinder. There's 0.250" rod in the drill chuck to catch the piece as it's cut through.

Another view. Was pretty liberal with the cutting fluid.

Here's the piece "caught".

Cut two more weights--each 12mm long. At this point, the quick part of the project took a turn and became an exercise in machining. Sometimes, easy is too easy. I wanted the two smaller weights to equal each other exactly and I wanted them together to weigh as much as the single large weight. Why? Why indeed. It's for an airgun. What else can I say?

After deburring, it was a matter of weighing and facing and weighing and...Until they were very, very close.

Found center lines on each, and spotted, drilled, tapped M5 x 0.8mm for setscrews.

Started the threading in the drill press for alignment, finished by hand with a plug tap. After sorting through the bin of M5 setscrews, I finalized the weights--with the deburring tool. They were that close. The largest weighs 20.6 grams. The two smaller, half that, at 10.3 grams each.

Since this was already pushing the absurd for a couple aluminum tubes, I hand-stamped the weights into each piece then gave them a brushed satin finish.

Installed.

Gapped,

or scrunched together.





This just might be the project that clearly shows just how far wrong I've gone. And the weights are closer than a tenth of a gram.

Monday, December 6, 2010

Rochester Disassembly, Part 3, Valves #2-#5

So left confused by the fact that the valve was soldered to the tube on the first Rochester, I disassembled the other 4 rifles…

12061001

Rochester #2. This is the 2nd best one.

12061002

The butt stock is actually in better shape.

12061003

Receiver.

12061004

Missing screws in the barrel band though.

12061005

And those are unlike the screws used in the other ones.

12061006

Roll pin instead of a solid pin.

12061007

Different pump head. Just a little grease…

12061008

Pump head.

12061009

The nut that retains the hammer spring is different.

12061010

Nut, spring and hammer sleeve.

12061011

All the other Rochesters had this type of nut, and only one nut.

12061012

The valve on this one is soldered to the tube as well.

12061013

You can see the smearing of solder on the brass.

12061014

So I took apart another Rochester, #3. It’s also soldered but has a brass ring as well. Not sure why.

12061015

The 4th valve wasn’t soldered, as far as I could tell. However mechanical means would not unscrew it. It seems to have a cement-like substance between the halves. Probably need heat anyway.

12061016

And the fifth valve is soldered to the tube.

12031027

Here’s the valve from Rochester #1 again, just so the valves are all on one page.

So four out of five valve assemblies are soldered to the tube. Next up it to make a vise block that snugly fits the valve body and a wrench that fits the tube (somewhat like a barrel vise and wrench), then use a propane torch to heat up the join and see if I can unscrew the halves. Sounds like fun…