Saturday, January 8, 2011

Hit a Gun Show

A buddy and I went to the Albany Lions Club Gun Show today.

01081101

Ok, It’s not an airgun, but tell me you wouldn’t have bought it?

01081102

By Wham-o, back when toys were dangerous. Actually this is a dangerous toy as the aluminum prod could break and injure you.

01081103

Ugly.

01081104

I have no idea what the scale is for.

01081105

Powermaster.

01081106

The prod is mounted with a J bolt.

01081108

see, a J bolt.

01081109

Something nice to hang on the wall.

01081110

Catch housing.

01081111

I’ll have to take it apart and get a better look later.

01081112

An A.B.T. shooting gallery rifle.

01081113

The bolt handle doesn’t actually run a bolt, just moves the slide back.

01081114

Odd rear sight.

01081115

Another view.

01081116

Patent list.

01081117

Where the air hose connects.

01081118

I presume you load it here. This will also get taken apart later.

You never know what you’ll find at a gun show. I also got a Plainsman BB pistol thrown in with the A.B.T. but it unfortunately works. I passed on a Crosman 130 that had some extreme finish issues. But it was cheap ($25 asking price). I missed a Crosman 760 with the wood stock and metal receiver ($10!) by about 30 seconds – a guy got it before I could. Oh well.

Now to get back to the accursed Rochester.

Wednesday, January 5, 2011

A Spare Magazine for an Aeron B96 Part 1

Nervous about posting part one before the mag is finished. There's still so much that can go wrong--and if it all goes down in flames, I'm not likely to tackle this again until I buy a proper milling machine.

Been looking around on the usual airgun classifieds, gunbroker, ebay...looking for a spare mag for my Aeron B96. They just aren't out there. Apparently, none of the importers ever had spare mags in any kind of quantity, either. The gun came with one single-shot and one five-shot mag. Gotta tell ya, when this gun comes out to play, 5 shots lasts about 2 seconds. In a perfect world, I'd have five or six spare magazines for this gun--OK, sure, I'd probably have ten. As I have to do this manually, I'm going to attempt to make exactly one.

How precise does the mag need to be to function correctly? That's my biggest concern. If the mag body isn't square, or the holes not the exact diameter, or parallel, or the height is off... I don't know if I have five thou of leeway or none. Will it shave lead off the pellets as they jump to the breech? Will it leak CO2?

The mag holds five .177 cal pellets and fits into a carrier on the pistol. The carrier indexes the magazine for each shot. The mag is just along for the ride.

Cut a piece of scrap aluminum to approximately the same length.

Set up the milling attachment and squared the milling vise.

For a change of pace, I used a homemade fly cutter instead of an end mill .



The fly cutter holds a lathe knife at an angle and swings it through an arc. The edge just skims across the work leaving a nice, flat surface in it's wake.



All I wanted for the first step was a flat side. The fly cutter did it in one pass.

I turned the piece around and zeroed the opposite side. My hope was that the fly cut side would make for an accurate base when milling the magazine to final width. There's a 1/4" HSS blank tool bit in the vise as a parallel--needed some stand off, otherwise the surface to be cut would be recessed in the jaws.

Milled the piece to 0.273"--the width of the mag.

Rotated the piece 90 degrees fly cut the face, then milled the opposite side, making the piece 0.280" in height.

A bit of clean up on the edges and corners then the ends were milled square to a final OAL of 1.687"

I guess part one should've just been titled: "Derrick makes an aluminum rectangle". Give me a few days, I'll let you know how it goes.